RC and 3D Printing
-
wrote on 29 Jan 2022, 15:02 last edited by
How expensive is the filament for this type of project?
IOW, without all the "other stuff" that goes into an RC airplane of this size, what's the cost of materials?
-
How expensive is the filament for this type of project?
IOW, without all the "other stuff" that goes into an RC airplane of this size, what's the cost of materials?
-
@george-k So far I have used about $12 in filament. After every thing is printed I suspect it will be between $20 and $30
wrote on 29 Jan 2022, 16:31 last edited by@mark said in RC and 3D Printing:
@george-k So far I have used about $12 in filament. After every thing is printed I suspect it will be between $20 and $30
And how much for the non-printable parts?
You said this looks like a pretty big plane. How flyable by an amateur?
-
@mark said in RC and 3D Printing:
@george-k So far I have used about $12 in filament. After every thing is printed I suspect it will be between $20 and $30
And how much for the non-printable parts?
You said this looks like a pretty big plane. How flyable by an amateur?
wrote on 29 Jan 2022, 18:45 last edited by@george-k It will be a trainer type plane. Not too fast and jittery. Slow and comfy, like a big old luxury sedan.
Reprint of Body Segment 12 in PLA silver after failed print in PETG. The PETG was not 100% at fault. This part needs printed supports for the internal bracing.
The designer recommended that I print in PLA vs. PETG. Most of the plane is already printed in PETG. I have to try this PLA print to see if what he says about the quality of the finished product is true. If it is significantly better, I will be reprinting some parts.
-
wrote on 30 Jan 2022, 00:48 last edited by
Frustrating. The 2nd attempt to print body segment 12 in PLA, failed. Hopefully this one will work. Back to PETG but with some internal supports. |
New Stream! Click it!
-
Frustrating. The 2nd attempt to print body segment 12 in PLA, failed. Hopefully this one will work. Back to PETG but with some internal supports. |
New Stream! Click it!
wrote on 30 Jan 2022, 00:49 last edited by@mark said in RC and 3D Printing:
2nd attempt to print body segment 12 in PLA, failed
Why does it fail? What happens?
-
wrote on 30 Jan 2022, 01:47 last edited by mark
Various things can make a print fail. In this instance, the walls on these parts are the thinnest I have ever seen in a 3D printed model. Every part has some "defects" that I need to go over with some epoxy and possibly some thin fiberglass cloth to rienforce the structural integrity.
The particular part failed the first time because I didn't use supports. The second time was due to it cracking apart when I attempted to remove it from the build plate.
-
wrote on 30 Jan 2022, 14:20 last edited by
Finally got Body segment 12 to print. Back to PETG filament.
Segments 13 & 14 printing now.
New stream. Click it!
-
Various things can make a print fail. In this instance, the walls on these parts are the thinnest I have ever seen in a 3D printed model. Every part has some "defects" that I need to go over with some epoxy and possibly some thin fiberglass cloth to rienforce the structural integrity.
The particular part failed the first time because I didn't use supports. The second time was due to it cracking apart when I attempted to remove it from the build plate.
wrote on 30 Jan 2022, 14:24 last edited by@mark said in RC and 3D Printing:
The second time was due to it cracking apart when I attempted to remove it from the build plate.
I would love to have heard the words you used when that happened.
-
@mark said in RC and 3D Printing:
The second time was due to it cracking apart when I attempted to remove it from the build plate.
I would love to have heard the words you used when that happened.
wrote on 30 Jan 2022, 14:57 last edited by@george-k said in RC and 3D Printing:
@mark said in RC and 3D Printing:
The second time was due to it cracking apart when I attempted to remove it from the build plate.
I would love to have heard the words you used when that happened.
It was definitely NSFW.
-
wrote on 30 Jan 2022, 16:03 last edited by Copper
We will need the first flight video, posted here.
-
wrote on 30 Jan 2022, 16:35 last edited by mark
-
wrote on 30 Jan 2022, 21:49 last edited by
New Part. Body Segment 16. Motor mount and cowl are next.
Click the link!
-
wrote on 31 Jan 2022, 00:52 last edited by brenda
@copper said in RC and 3D Printing:
We will need the first flight video, posted here.
+++ eleventy bajillion
-
@copper said in RC and 3D Printing:
We will need the first flight video, posted here.
+++ eleventy bajillion
wrote on 31 Jan 2022, 02:10 last edited by@brenda Absolutely! Like I was trying to emote back to Copper, I hope it it not its last flight. lol
Last one tonight. The Engine Cowl. 10.25 hour print job.
I think I have enough filament on the roll but time will tell...
Click it! -
wrote on 31 Jan 2022, 15:10 last edited by
-
wrote on 31 Jan 2022, 23:36 last edited by
-
wrote on 31 Jan 2022, 23:47 last edited by
For the record, I click on every update...
You're welcome.
-
wrote on 1 Feb 2022, 08:16 last edited by
